List of Poster Presentations
FFW1070
Friction Coefficient of Cu-Ni-In and CoCrAlYSi–hBN Coated Ti-6Al-4V Fretted Against Alumina Counterbody with and without MoS2 at the Contact Surface
Mr Abhinay Seelamanthula
IIT Madras
FFW1020
Crowd Management for Power Generation.
Mr. Abdulaziz Alnuman
Cranfield University
FFW1129
Acoustic wear monitoring during the milling of tool steel for machining 4.0
Prof Khaled ABOU-EL-HOSSEIN
Nelson Mandela University, South Africa
FFW1152
Numerical Analysis of the Wind Turbine Pitch Bearing Raceway Tribo-Contact Due to Cyclic Loading under Constant Pitch Angle_V2
Mr. David Cubillas
Ikerlan Technology Research Centre
FFW1107
Sensitivity of Damping for Diagnostics of Damage in Structure
Anatoliy Bovsunovsky
Professor, Department of Cogeneration Installations of Thermal and Nuclear Power Plants, National Technical University of Ukraine "Igor Sikorsky Kyiv Polytechnic Institute"
FFW1133
D-Beam theory for Functionally Graded Double Cantilever Beam analysis
Prof. Calogero Orlando
Kore University of Enna
FFW1134
Study of wear on AISI E52100 steel using a lithium complex grease and a calcium sulfonate grease
Dr. Manuel Vite-Torres
INSTITUTO POLITÉCNICO NACIONAL, MÉXICO
FFW1121
Failure Analysis of a Fuel Control Tube from an Aircraft Engine
Dr. Maria Garcia-Martinez
FFW1086
Depreciation Accounting in Longevity Evaluation of the Complicated Systems B. Avotyn1*, A. Smirnov2, B. Belobragin3 1 Chief of reliability division, JSC “SPLAV SPA after A. Ganichev”, RF 2 Managing director, JSC “SPLAV SPA after A. Ganichev”, RF 3 Deputy Director General, Chief Designer, JSC “SPLAV SPA after A. Ganichev”, RF *Corresponding author: E-mail bavotyn@mail.ru & Phone: (4872) 464553
Dr. Avotyn' Boris Andreevich
Chief of reliability division, JSC “SPLAV SPA after A. Ganichev”, RF
FFW1112
Effect of Cross-Over Fraction on Objective Function Value in Genetic Algorithm Optimization of Machining Parameters in Diamond Turning of Aluminum Alloy (RSA-431) For Optical Applications
Prof Khaled ABOU-EL-HOSSEIN
Nelson Mandela University, South Africa
FFW1135
The application of an image-processing method and fractal analysis for quantitative characterization of thermal cracks in a cement matrix
Dr. Maciej Szelag
Lublin University of Technology
FFW1064
Determination of the effective stiffness of half-open cross-section bars and orthotropic steel deck of a truss bridge using model updating
Dr. Long Viet Ho
Faculty of Civil Engineering, Campus in Ho Chi Minh City, University of Transport and Communications
FFW1137
Coincidence of stereometric and tribometric studies of friction pair components
Prof. Niemczewska-Wójcik Magdalena
Cracow University of Technology
FFW1138
Numerical treatment of fractional differential models
Prof. Angelamaria Cardone
FFW1142
Mode shape based approach to identify the location of crack and the influence of crack on critical speed of gas turbine disc
Prof. Vinayak Ranjan
Professor and Head , Department of Mechanical and Aerospace Engineering, Bennett University, Greater Noida, India
FFW1143
Time-delay fractional optimal control problems: A survey based on methodology
Dr. Leila Moradi
University of Salerno
FFW1002
A model for prediction and optimization of Flank wear in End milling of AISI 316 stainless steel
Prof Khaled ABOU-EL-HOSSEIN
Nelson Mandela University, South Africa
FFW1095
Application of improved artificial neural network to stiffness reduction analysis of truss joints in a railway bridge
Dr. Hoa Tran
Department of Electrical Energy, Metals, Mechanical Constructions, and Systems, Faculty of Engineering and Architecture, Ghent University, 9000 Gent, Belgium
FFW1126
Study of Pre-strain Effect on Bendability in Three-point Bending Test
Mr. Mohammadmehdi Shahzamanian Sichani
McMaster University
FFW1104
Hydrogen degradation effects on crack propagation in high-strength steels: a fully coupled approach
Dr. Behnam Sobhaniaragh
University of Sao Paulo